# American Institute of Mathematical Sciences

September  2020, 16(5): 2117-2139. doi: 10.3934/jimo.2019046

## Nonlinear optimization to management problems of end-of-life vehicles with environmental protection awareness and damaged/aging degrees

 1 School of Mathematics and Statistics, Central South University, Changsha 410083, China 2 Experimental Teaching Center, Guangdong University of Foreign Studies, Guangzhou 510420, China

* Corresponding authors: Zhong Wan and Jing Zhang

Received  November 2018 Revised  December 2018 Published  September 2020 Early access  May 2019

Fund Project: The first and second authors are supported by the National Science Foundation of China (Grant No. 71671190)

In the past one decade, an increasing number of motor vehicles necessarily results in huge amounts of end-of-life vehicles (ELVs) in the future. From the view point of environment protection and resource utilization, government subsidy and public awareness of environmental protection play a critical role in promoting the formal recycle enterprises to recycle the ELVs as many as possible. Different from the existing similar models, a mixed integer nonlinear optimization model is established in this paper to formulate the management problems of recycling ELVs as a centralized decision-making system, where damaged and aging degrees, correlation between the recycled quantity and take-back price of ELVs, and the public environmental protection awareness are considered. Unlike the results available in the literature, take-back prices of the ELVs are the endogenous variables of the model (decision variables), which affect the collected quantity of ELVs and the profit of recycling system. Additionally, due to distinct damaged and aging degrees of the ELVs, the refurbished or dismantled amounts of ELVs are also regarded as the decision variables so that the recycle system is more applicable. By case study and sensitivity analysis, validity of the model is verified and impacts of the governmental subsidy and environmental awareness are analyzed. By the proposed model, it is revealed that: (1) Distinct treatment of ELVs with different damaged and aging degrees can increase the profit of recycling ELVs; (2) Compared with the transportation cost, higher processing cost is a main obstacle to the profit growth. Advanced processing technology plays the most important role in improving the ELV recovery efficiency. (3) Both of government subsidy and environmental awareness seriously affect decision-making of recycle enterprises.

Citation: Zhong Wan, Jingjing Liu, Jing Zhang. Nonlinear optimization to management problems of end-of-life vehicles with environmental protection awareness and damaged/aging degrees. Journal of Industrial and Management Optimization, 2020, 16 (5) : 2117-2139. doi: 10.3934/jimo.2019046
##### References:
 [1] J. P. Arnaout, G. Arnaout and J. Khoury, Simulation and optimization of ant colony optimization algorithm for the stochastic uncapacitated location-allocation problem, Journal of Industrial and Management Optimization, 12 (2016), 1215-1225.  doi: 10.3934/jimo.2016.12.1215. [2] P. Ávila-Torres, F. López-Irarragorri, R. Caballero and et al., The multimodal and multiperiod urban transportation integrated timetable construction problem with demand uncertainty Journal of Industrial and Management Optimization, 14 (2018), 447-472. doi: 10.3934/jimo.2017055. [3] J. B. Bahersa and J. Kim, Regional approach of waste electrical and electronic equipment (WEEE) management in France, Resources, Conservation and Recycling, 129 (2018), 45-55.  doi: 10.1016/j.resconrec.2017.10.016. [4] X. R. Chen, Y. M. Liu and Z. Wan, Optimal decision-making for the online and offline retailers under BOPS model, The ANZIAM Journal, 58 (2016), 187-208.  doi: 10.1017/S1446181116000201. [5] E. Demirel, N. Demirel and H. Gökçen, A mixed integer linear programming model to optimize reverse logistics activities of end-of-life vehicles in Turkey, Journal of Cleaner Production, 112 (2016), 2101-2113.  doi: 10.1016/j.jclepro.2014.10.079. [6] S. H. Hu and Z. G. Wen, Monetary evaluation of end-of-life vehicle treatment from a social perspective for different scenarios in China, Journal of Cleaner Production, 159 (2017), 257-270.  doi: 10.1016/j.jclepro.2017.05.042. [7] S. T. John, R. Sridharan, P. N. Ram Kumar and M. Krishnamoorthy, Multi-period reverse logistics network design for used refrigerators., Applied Mathematical Modelling, 54 (2018), 311-331.  doi: 10.1016/j.apm.2017.09.053. [8] O. Kaya and B. Urek, A mixed integer nonlinear programming model and heuristic solutions for location, inventory and pricing decisions in a closed loop supply chain, Computers and Operations Research, 65 (2016), 93-103.  doi: 10.1016/j.cor.2015.07.005. [9] W. C. Li, H. T. Bai, J. F. Yin and H. Xu, Life cycle assessment of end-of-life vehicle recycling processes in China-take Corolla taxis for example, Journal of Cleaner Production, 117 (2016), 176-187.  doi: 10.1016/j.jclepro.2016.01.025. [10] J. Y. Li, X. Hu and Z. Wan, An integrated bi-objective optimization model and improved genetic algorithm for vehicle routing problems with temporal and spatial constraints, Journal of Industrial and Management Optimization, online first (2018). doi: 10.3934/jimo.2018200. [11] Y. X. Li, Z. Wan and J. J. Liu, Bi-level programming approach to optimal strategy for VMI problems under random demand, The ANZIAM Journal, 59 (2017), 247-270.  doi: 10.1017/S1446181117000384. [12] H. H. Liu, M. Lei, H. H. Deng, G. K. Leong and T. Huang, A dual channel, quality-based price competition model for the WEEE recycling market with government subsidy, Omega, 59 (2016), 290-302.  doi: 10.1016/j.omega.2015.07.002. [13] Y. X. Pan and H. T. Li, Sustainability evaluation of end-of-life vehicle recycling based on emergy analysis: a case study of an end-of-life vehicle recycling enterprise in China, Journal of Cleaner Production, 131 (2016), 219-227.  doi: 10.1016/j.jclepro.2016.05.045. [14] P. N. K. Phuc, V. F. Yu and Y. C. Tsao, Optimizing fuzzy reverse supply chain for end-of-life vehicles, Computers and Industrial Engineering, 113 (2017), 757-765.  doi: 10.1016/j.cie.2016.11.007. [15] I. Polak and N. Privault, A stochastic newsvendor game with dynamic retail prices, Journal of Industrial and Management Optimization, 14 (2018), 731-742.  doi: 10.3934/jimo.2017072. [16] V. Simic, Interval-parameter chance-constraint programming model for end-of-life vehicles management under rigorous environmental regulations, Waste Management, 52 (2016), 180-192.  doi: 10.1016/j.wasman.2016.03.044. [17] K. Subulan, A. S. Taşan and A. Baykasoğlu, A fuzzy goal programming model to strategic planning problem of a lead/acid battery closed-loop supply chain, Journal of Manufacturing Systems, 37 (2015), 243-264.  doi: 10.1016/j.jmsy.2014.09.001. [18] Q. Sun, C. Wang, L. S. Zuo and F. H. Lu, Digital empowerment in a WEEE collection business ecosystem: A comparative study of two typical cases in China, Journal of Cleaner Production, 184 (2018), 414-422.  doi: 10.1016/j.jclepro.2018.02.114. [19] Z. Wan, H. Wu and L. Dai, A polymorphic uncertain equilibrium model and its deterministic equivalent formulation for decentralized supply chain management, Applied Mathematical Modelling, 58 (2018), 281-299.  doi: 10.1016/j.apm.2017.06.028. [20] Z. Wan, S. J. Zhang and K. L. Teo, Polymorphic uncertain nonlinear programming approach for maximizing the capacity of V-belt driving, Optimization and Engineering, 15 (2014), 267-292.  doi: 10.1007/s11081-012-9205-3. [21] Y. X. Wang, X. Y. Chang, Z. G. Chen, Y. G. Zhong and T. J. Fan, Impact of subsidy policies on recycling and remanufacturing using system dynamics methodology: a case of auto parts in China, Journal of Cleaner Production, 74 (2014), 161-171.  doi: 10.1016/j.jclepro.2014.03.023. [22] X. Wang and M. Chen, Implementing extended producer responsibility: Vehicle remanufacturing in China, Journal of Cleaner Production, 19 (2011), 680-686. [23] L. Wang and M. Chen, Policies and perspective on end-of-life vehicles in China, Journal of Cleaner Production, 44 (2013), 168-176.  doi: 10.1016/j.jclepro.2012.11.036. [24] H. Wu and Z. Wan, A multi-objective optimization model and orthogonal design based hybrid heuristic algorithm for regional urban mining management problems., Journal of the Air and Waste Management Association, 68 (2018), 146-169. [25] T. Z. Zhang, J. W. Chu, X. P. Wang, X. H. Liu and P. F. Cui, Development pattern and enhancing system of automotive components remanufacturing industry in China, Resources, Conservation and Recycling, 55 (2011), 613-622.  doi: 10.1016/j.resconrec.2010.09.015. [26] X. B. Zhang, S. Huang and Z. Wan, Optimal pricing and ordering in global supply chain management with constraints under random demand, Applied Mathematical Modelling, 40 (2016), 10105-10130.  doi: 10.1016/j.apm.2016.06.054. [27] Q. H. Zhao and M. Chen, A comparison of ELV recycling system in China and Japan and China's strategies, Resources, Conservation and Recycling, 57 (2011), 15-21.  doi: 10.1016/j.resconrec.2011.09.010.

show all references

##### References:
 [1] J. P. Arnaout, G. Arnaout and J. Khoury, Simulation and optimization of ant colony optimization algorithm for the stochastic uncapacitated location-allocation problem, Journal of Industrial and Management Optimization, 12 (2016), 1215-1225.  doi: 10.3934/jimo.2016.12.1215. [2] P. Ávila-Torres, F. López-Irarragorri, R. Caballero and et al., The multimodal and multiperiod urban transportation integrated timetable construction problem with demand uncertainty Journal of Industrial and Management Optimization, 14 (2018), 447-472. doi: 10.3934/jimo.2017055. [3] J. B. Bahersa and J. Kim, Regional approach of waste electrical and electronic equipment (WEEE) management in France, Resources, Conservation and Recycling, 129 (2018), 45-55.  doi: 10.1016/j.resconrec.2017.10.016. [4] X. R. Chen, Y. M. Liu and Z. Wan, Optimal decision-making for the online and offline retailers under BOPS model, The ANZIAM Journal, 58 (2016), 187-208.  doi: 10.1017/S1446181116000201. [5] E. Demirel, N. Demirel and H. Gökçen, A mixed integer linear programming model to optimize reverse logistics activities of end-of-life vehicles in Turkey, Journal of Cleaner Production, 112 (2016), 2101-2113.  doi: 10.1016/j.jclepro.2014.10.079. [6] S. H. Hu and Z. G. Wen, Monetary evaluation of end-of-life vehicle treatment from a social perspective for different scenarios in China, Journal of Cleaner Production, 159 (2017), 257-270.  doi: 10.1016/j.jclepro.2017.05.042. [7] S. T. John, R. Sridharan, P. N. Ram Kumar and M. Krishnamoorthy, Multi-period reverse logistics network design for used refrigerators., Applied Mathematical Modelling, 54 (2018), 311-331.  doi: 10.1016/j.apm.2017.09.053. [8] O. Kaya and B. Urek, A mixed integer nonlinear programming model and heuristic solutions for location, inventory and pricing decisions in a closed loop supply chain, Computers and Operations Research, 65 (2016), 93-103.  doi: 10.1016/j.cor.2015.07.005. [9] W. C. Li, H. T. Bai, J. F. Yin and H. Xu, Life cycle assessment of end-of-life vehicle recycling processes in China-take Corolla taxis for example, Journal of Cleaner Production, 117 (2016), 176-187.  doi: 10.1016/j.jclepro.2016.01.025. [10] J. Y. Li, X. Hu and Z. Wan, An integrated bi-objective optimization model and improved genetic algorithm for vehicle routing problems with temporal and spatial constraints, Journal of Industrial and Management Optimization, online first (2018). doi: 10.3934/jimo.2018200. [11] Y. X. Li, Z. Wan and J. J. Liu, Bi-level programming approach to optimal strategy for VMI problems under random demand, The ANZIAM Journal, 59 (2017), 247-270.  doi: 10.1017/S1446181117000384. [12] H. H. Liu, M. Lei, H. H. Deng, G. K. Leong and T. Huang, A dual channel, quality-based price competition model for the WEEE recycling market with government subsidy, Omega, 59 (2016), 290-302.  doi: 10.1016/j.omega.2015.07.002. [13] Y. X. Pan and H. T. Li, Sustainability evaluation of end-of-life vehicle recycling based on emergy analysis: a case study of an end-of-life vehicle recycling enterprise in China, Journal of Cleaner Production, 131 (2016), 219-227.  doi: 10.1016/j.jclepro.2016.05.045. [14] P. N. K. Phuc, V. F. Yu and Y. C. Tsao, Optimizing fuzzy reverse supply chain for end-of-life vehicles, Computers and Industrial Engineering, 113 (2017), 757-765.  doi: 10.1016/j.cie.2016.11.007. [15] I. Polak and N. Privault, A stochastic newsvendor game with dynamic retail prices, Journal of Industrial and Management Optimization, 14 (2018), 731-742.  doi: 10.3934/jimo.2017072. [16] V. Simic, Interval-parameter chance-constraint programming model for end-of-life vehicles management under rigorous environmental regulations, Waste Management, 52 (2016), 180-192.  doi: 10.1016/j.wasman.2016.03.044. [17] K. Subulan, A. S. Taşan and A. Baykasoğlu, A fuzzy goal programming model to strategic planning problem of a lead/acid battery closed-loop supply chain, Journal of Manufacturing Systems, 37 (2015), 243-264.  doi: 10.1016/j.jmsy.2014.09.001. [18] Q. Sun, C. Wang, L. S. Zuo and F. H. Lu, Digital empowerment in a WEEE collection business ecosystem: A comparative study of two typical cases in China, Journal of Cleaner Production, 184 (2018), 414-422.  doi: 10.1016/j.jclepro.2018.02.114. [19] Z. Wan, H. Wu and L. Dai, A polymorphic uncertain equilibrium model and its deterministic equivalent formulation for decentralized supply chain management, Applied Mathematical Modelling, 58 (2018), 281-299.  doi: 10.1016/j.apm.2017.06.028. [20] Z. Wan, S. J. Zhang and K. L. Teo, Polymorphic uncertain nonlinear programming approach for maximizing the capacity of V-belt driving, Optimization and Engineering, 15 (2014), 267-292.  doi: 10.1007/s11081-012-9205-3. [21] Y. X. Wang, X. Y. Chang, Z. G. Chen, Y. G. Zhong and T. J. Fan, Impact of subsidy policies on recycling and remanufacturing using system dynamics methodology: a case of auto parts in China, Journal of Cleaner Production, 74 (2014), 161-171.  doi: 10.1016/j.jclepro.2014.03.023. [22] X. Wang and M. Chen, Implementing extended producer responsibility: Vehicle remanufacturing in China, Journal of Cleaner Production, 19 (2011), 680-686. [23] L. Wang and M. Chen, Policies and perspective on end-of-life vehicles in China, Journal of Cleaner Production, 44 (2013), 168-176.  doi: 10.1016/j.jclepro.2012.11.036. [24] H. Wu and Z. Wan, A multi-objective optimization model and orthogonal design based hybrid heuristic algorithm for regional urban mining management problems., Journal of the Air and Waste Management Association, 68 (2018), 146-169. [25] T. Z. Zhang, J. W. Chu, X. P. Wang, X. H. Liu and P. F. Cui, Development pattern and enhancing system of automotive components remanufacturing industry in China, Resources, Conservation and Recycling, 55 (2011), 613-622.  doi: 10.1016/j.resconrec.2010.09.015. [26] X. B. Zhang, S. Huang and Z. Wan, Optimal pricing and ordering in global supply chain management with constraints under random demand, Applied Mathematical Modelling, 40 (2016), 10105-10130.  doi: 10.1016/j.apm.2016.06.054. [27] Q. H. Zhao and M. Chen, A comparison of ELV recycling system in China and Japan and China's strategies, Resources, Conservation and Recycling, 57 (2011), 15-21.  doi: 10.1016/j.resconrec.2011.09.010.
Material flow of the ELV recovery network
The map and the existent ELV recycling network in Hunan
Effect of public environmental protection awareness
Impacts of subsidy
Impact of different types of costs on profit
Impacts of different types of costs on the recycled quantities
Number of different types of nodes in ELV recovery network
 $I$ $J$ $O$ $K$ $L$ $U$ $S$ $P$ $Q$ $R$ $V$ $W$ $M$ $N$ 5 5 2 6 5 2 2 2 2 2 2 2 2 2
 $I$ $J$ $O$ $K$ $L$ $U$ $S$ $P$ $Q$ $R$ $V$ $W$ $M$ $N$ 5 5 2 6 5 2 2 2 2 2 2 2 2 2
Distribution of nodes in ELV recovery network
 Changsha Zhuzhou Xiangtan Hengyang Shaoyang Resource 1 2 3 4 5 Collection center 1 2 3 4 5 Repair center 1, 2 - - - - Dismantler 1 2, 3 4 6 5 Shredder 2 1 3 5 4 Landfill 2 - 1 - - Steel mill 1, 2 - - - - Non-ferrous smeltery 1 - - 2 - Oil factory 1, 2 - - - - Battery factory 1 - - 2 - Rubber factory - 1 - - 2 Glass factory 1, 2 - - - - Plastics factory - - 1 - 2
 Changsha Zhuzhou Xiangtan Hengyang Shaoyang Resource 1 2 3 4 5 Collection center 1 2 3 4 5 Repair center 1, 2 - - - - Dismantler 1 2, 3 4 6 5 Shredder 2 1 3 5 4 Landfill 2 - 1 - - Steel mill 1, 2 - - - - Non-ferrous smeltery 1 - - 2 - Oil factory 1, 2 - - - - Battery factory 1 - - 2 - Rubber factory - 1 - - 2 Glass factory 1, 2 - - - - Plastics factory - - 1 - 2
Distance between the nodes of network (km)
 Collection center 1 2 3 4 5 Resources 1 10 67.4 46.9 152 148.3 2 49.8 20.2 26.9 117 133.6 3 43.7 27.2 13.4 111.4 122.1 4 147.6 100.7 104.8 6.1 75.5 5 170.2 170.5 146.8 109.9 43.5 Repair certer 1 29.4 40.9 28 131 137.6 2 155.9 133.2 120.6 51.8 26.9 Dismantler 1 21.8 59.8 46.4 150.9 153.1 2 60.2 13.8 36.3 116.4 138.7 3 49.8 22.9 31.9 122.2 139.2 4 124.9 64.8 81.8 48.8 105.1 5 148.8 143.3 121.6 84.3 15.5 6 144.2 107.3 103.6 16.6 53.3
 Collection center 1 2 3 4 5 Resources 1 10 67.4 46.9 152 148.3 2 49.8 20.2 26.9 117 133.6 3 43.7 27.2 13.4 111.4 122.1 4 147.6 100.7 104.8 6.1 75.5 5 170.2 170.5 146.8 109.9 43.5 Repair certer 1 29.4 40.9 28 131 137.6 2 155.9 133.2 120.6 51.8 26.9 Dismantler 1 21.8 59.8 46.4 150.9 153.1 2 60.2 13.8 36.3 116.4 138.7 3 49.8 22.9 31.9 122.2 139.2 4 124.9 64.8 81.8 48.8 105.1 5 148.8 143.3 121.6 84.3 15.5 6 144.2 107.3 103.6 16.6 53.3
Distance between the nodes of network (Continued Table 3)
 Shredder Secondary market 1 2 3 4 5 1 2 Dismantler 1 123.2 25.1 39.1 194.6 42.0 10.2 2.3 2 75.3 50.7 33.4 182.8 21.9 39.5 46.7 3 85.8 42.6 27.2 183.0 17.8 28.8 36.1 4 40.4 129.2 87.1 145.2 80.1 111.6 119.8 5 160.2 185.1 128.4 31.7 134.1 155.2 160.8 6 100.7 165.6 110.9 87.1 110.3 140.1 147.7 Landfill 1 148.7 39.4 59.5 204.0 65.3 - - 2 88.1 50.9 14.4 170.2 4.7 - - Steel mill 1 117.8 33.0 29.7 185.1 33.8 - - 2 114.7 33.3 27.2 184.0 30.8 - - Non-ferrous smeltery 1 149.4 33.0 65.3 214.1 69.3 - - 2 75.7 156.5 106.2 113.9 102.7 - -
 Shredder Secondary market 1 2 3 4 5 1 2 Dismantler 1 123.2 25.1 39.1 194.6 42.0 10.2 2.3 2 75.3 50.7 33.4 182.8 21.9 39.5 46.7 3 85.8 42.6 27.2 183.0 17.8 28.8 36.1 4 40.4 129.2 87.1 145.2 80.1 111.6 119.8 5 160.2 185.1 128.4 31.7 134.1 155.2 160.8 6 100.7 165.6 110.9 87.1 110.3 140.1 147.7 Landfill 1 148.7 39.4 59.5 204.0 65.3 - - 2 88.1 50.9 14.4 170.2 4.7 - - Steel mill 1 117.8 33.0 29.7 185.1 33.8 - - 2 114.7 33.3 27.2 184.0 30.8 - - Non-ferrous smeltery 1 149.4 33.0 65.3 214.1 69.3 - - 2 75.7 156.5 106.2 113.9 102.7 - -
Distance between the nodes of network (Continued Table 4)
 Oil Battery Rubber Glass Plastics 1 2 1 2 1 2 1 2 1 2 ND 1 12.8 8.7 6.6 177.7 36.1 200.6 7.6 5.5 43.3 164.6 2 53.4 53.8 42.7 143.54 17.3 191.5 40.6 51.3 29.0 144.2 3 42.8 43.6 32.1 149.3 9.8 191.2 30.1 41.0 24.5 146.3 4 121.9 129.2 115.2 72.9 85.6 157.5 115.3 126.2 81.0 98.2 5 153.6 171.4 157.5 86.9 142.9 39.9 161.9 168.5 128.1 31.5 6 145.1 158.6 143.4 30.7 118.5 100.2 145.7 155.4 107.1 39.8
 Oil Battery Rubber Glass Plastics 1 2 1 2 1 2 1 2 1 2 ND 1 12.8 8.7 6.6 177.7 36.1 200.6 7.6 5.5 43.3 164.6 2 53.4 53.8 42.7 143.54 17.3 191.5 40.6 51.3 29.0 144.2 3 42.8 43.6 32.1 149.3 9.8 191.2 30.1 41.0 24.5 146.3 4 121.9 129.2 115.2 72.9 85.6 157.5 115.3 126.2 81.0 98.2 5 153.6 171.4 157.5 86.9 142.9 39.9 161.9 168.5 128.1 31.5 6 145.1 158.6 143.4 30.7 118.5 100.2 145.7 155.4 107.1 39.8
Capacity (ton) and unit processing cost (yuan RMB/ton)
 ${ca}_{j}$ ${ca}_{k}$ ${ca}_{l}$ ${ca}_{u}$ $pc_{1o}$ $pc_{2o}$ $pc_k$ $pc_l$ $pc_u$ 2000 2000 1500 500 2000 3000 1960 270 500
 ${ca}_{j}$ ${ca}_{k}$ ${ca}_{l}$ ${ca}_{u}$ $pc_{1o}$ $pc_{2o}$ $pc_k$ $pc_l$ $pc_u$ 2000 2000 1500 500 2000 3000 1960 270 500
Unit transportation cost (yuan RMB/ton·km)
 $tc_{ij}$ $tc_{jo}$ $tc_{jk}$ $tc_{kl}$ $tc_{lu}$ $tc_{ks}$ $tc_{kp}$ $tc_{lm}$ $tc_{ln}$ $tc_{kq}$ $tc_{kr}$ $tc_{kv}$ $tc_{kw}$ 2 1 0.8 0.4 1 1.5 0.7 0.6 0.5 0.5 0.5 0.7 0.7
 $tc_{ij}$ $tc_{jo}$ $tc_{jk}$ $tc_{kl}$ $tc_{lu}$ $tc_{ks}$ $tc_{kp}$ $tc_{lm}$ $tc_{ln}$ $tc_{kq}$ $tc_{kr}$ $tc_{kv}$ $tc_{kw}$ 2 1 0.8 0.4 1 1.5 0.7 0.6 0.5 0.5 0.5 0.7 0.7
Unit selling prices of recyled components (×103 yuan RMB/ton)
 $s$ $s_{0}$ $s_{1}$ $s_{2}$ $s_{3}$ $s_{4}$ $s_{5}$ $s_{6}$ $s_{7}$ $z_{1}$ $z_{2}$ 3000 50000 2400 12000 4000 600 150 450 6000 500 1500 $s^{'}_{1}$ $s^{'}_{2}$ $s^{'}_{3}$ $s^{'}_{4}$ $s^{'}_{5}$ $s^{'}_{6}$ $s^{'}_{7}$ $z^{'}_{1}$ $z^{'}_{2}$ 27360 136800 45600 6840 17100 5130 68400 5700 17100
 $s$ $s_{0}$ $s_{1}$ $s_{2}$ $s_{3}$ $s_{4}$ $s_{5}$ $s_{6}$ $s_{7}$ $z_{1}$ $z_{2}$ 3000 50000 2400 12000 4000 600 150 450 6000 500 1500 $s^{'}_{1}$ $s^{'}_{2}$ $s^{'}_{3}$ $s^{'}_{4}$ $s^{'}_{5}$ $s^{'}_{6}$ $s^{'}_{7}$ $z^{'}_{1}$ $z^{'}_{2}$ 27360 136800 45600 6840 17100 5130 68400 5700 17100
Weight percentages in the recycled ELVs
 $alpha$ $beta_{1}$ $beta_{2}$ $beta_{3}$ $beta_{4}$ $beta_{5}$ $beta_{6}$ $beta_{7}$ $eta$ $eta_{1}$ $eta_{2}$ 0.81 0.06 0.04 0.017 0.013 0.03 0.015 0.015 15/81 62/81 4/81
 $alpha$ $beta_{1}$ $beta_{2}$ $beta_{3}$ $beta_{4}$ $beta_{5}$ $beta_{6}$ $beta_{7}$ $eta$ $eta_{1}$ $eta_{2}$ 0.81 0.06 0.04 0.017 0.013 0.03 0.015 0.015 15/81 62/81 4/81
Optimal solution in case study
 DV OS DV OS DV OS DV OS DV OS $\rho_{1,1}$ 15000 $A_{3,1,3}$ 119 $E_{3,2,5}$ 468.2 $Q3_{3,1}$ 92.8 $Q6_{2,1}$ 8.7 $\rho_{1,2}$ 15000 $A_{3,2,2}$ 578 $E_{3,3,5}$ 442.3 $Q3_{5,1}$ 106.4 $Q6_{3,1}$ 8.2 $\rho_{1,3}$ 15000 $A_{3,2,3}$ 9 $E_{3,5,3}$ 507.1 $Q3_{6,1}$ 111.5 $Q6_{5,1}$ 9.4 $\rho_{1,4}$ 15000 $A_{3,3,3}$ 418 $E_{3,6,3}$ 531.4 $Q3^{'}_{1,2}$ 34 $Q6_{6,1}$ 9.9 $\rho_{1,5}$ 14900 $A_{3,4,4}$ 656 $F_{3,2}$ 352.7 $Q3^{'}_{2,1}$ 34 $Q6^{'}_{1,2}$ 3 $\rho_{2,1}$ 10000 $A_{3,5,5}$ 626 $F_{5,2}$ 228.4 $Q3^{'}_{3,1}$ 34 $Q6^{'}_{2,1}$ 3 $\rho_{2,2}$ 10000 $B_{1,1,1}$ 150 $Q1_{1,2}$ 40.3 $Q3^{'}_{6,1}$ 34 $Q6^{'}_{3,1}$ 3 $\rho_{2,3}$ 10000 $B_{1,2,1}$ 150 $Q1_{2,1}$ 34.7 $Q4_{1,1}$ 8.7 $Q6^{'}_{6,1}$ 3 $\rho_{2,4}$ 10000 $B_{1,3,1}$ 150 $Q1_{3,1}$ 32.8 $Q4_{2,1}$ 7.5 $Q7_{1,1}$ 10.1 $\rho_{2,5}$ 9950 $B_{1,4,2}$ 150 $Q1_{5,1}$ 37.6 $Q4_{3,1}$ 7.1 $Q7_{2,1}$ 8.7 $\rho_{3,1}$ 501.4 $B_{1,5,2}$ 149 $Q1_{6,1}$ 39.4 $Q4_{5,2}$ 8.1 $Q7_{3,1}$ 8.19 $\rho_{3,2}$ 577.1 $B_{2,5,2}$ 199 $Q1^{'}_{1,2}$ 12 $Q4_{6,2}$ 8.5 $Q7_{5,2}$ 9.4 $\rho_{3,3}$ 600 $C_{2,1,1}$ 200 $Q1^{'}_{2,1}$ 12 $Q4^{'}_{1,1}$ 2.6 $Q7_{6,2}$ 9.84 $\rho_{3,4}$ 474.3 $C_{2,2,2}$ 200 $Q1^{'}_{3,1}$ 12 $Q4^{'}_{2,1}$ 2.6 $Q7^{'}_{1,1}$ 3 $\rho_{3,5}$ 435.7 $C_{2,3,3}$ 200 $Q1^{'}_{6,1}$ 12 $Q4^{'}_{3,1}$ 2.6 $Q7^{'}_{2,1}$ 3 $A_{1,1,1}$ 150 $C_{2,4,6}$ 200 $Q2_{1,2}$ 26.9 $Q4^{'}_{6,2}$ 2.6 $Q7^{'}_{3,1}$ 3 $A_{1,2,2}$ 150 $C_{3,1,1}$ 672 $Q2_{2,1}$ 23.1 $Q5_{1,1}$ 20.16 $Q7^{'}_{6,2}$ 3 $A_{1,3,3}$ 150 $C_{3,2,2}$ 578 $Q2_{3,1}$ 21.8 $Q5_{2,1}$ 17.3 $Q8_{3,2}$ 1210.8 $A_{1,4,4}$ 150 $C_{3,3,3}$ 546 $Q2_{5,1}$ 25.0 $Q5_{3,1}$ 16.4 $Q8_{5,2}$ 696.5 $A_{1,5,5}$ 149 $C_{3,4,6}$ 656 $Q2_{6,1}$ 26.2 $Q5_{5,2}$ 18.8 $Q8^{'}_{3,2}$ 247.9 $A_{2,1,1}$ 200 $C_{3,5,5}$ 626 $Q2^{'}_{1,2}$ 8 $Q5_{6,2}$ 19.7 $Q8^{'}_{5,2}$ 247.9 $A_{2,2,2}$ 200 $E_{2,1,3}$ 162 $Q2^{}_{2,1}$ 8 $Q5^{'}_{1,1}$ 6 $Q9_{3,1}$ 79.1 $A_{2,3,3}$ 200 $E_{2,2,5}$ 162 $Q2^{'}_{3,1}$ 8 $Q5^{'}_{2,1}$ 6 $Q9_{5,1}$ 45.5 $A_{2,4,4}$ 200 $E_{2,3,5}$ 162 $Q2^{'}_{6,1}$ 8 $Q5^{'}_{3,1}$ 6 $Q9^{'}_{3,1}$ 16.2 $A_{2,5,5}$ 199 $E_{2,6,3}$ 162 $Q3_{1,2}$ 114.2 $Q5^{'}_{6,2}$ 6 $Q9^{'}_{5,1}$ 16.2 $A_{3,1,1}$ 672 $E_{3,1,3}$ 544.3 $Q3_{2,1}$ 98.3 $Q6_{1,2}$ 10.1
 DV OS DV OS DV OS DV OS DV OS $\rho_{1,1}$ 15000 $A_{3,1,3}$ 119 $E_{3,2,5}$ 468.2 $Q3_{3,1}$ 92.8 $Q6_{2,1}$ 8.7 $\rho_{1,2}$ 15000 $A_{3,2,2}$ 578 $E_{3,3,5}$ 442.3 $Q3_{5,1}$ 106.4 $Q6_{3,1}$ 8.2 $\rho_{1,3}$ 15000 $A_{3,2,3}$ 9 $E_{3,5,3}$ 507.1 $Q3_{6,1}$ 111.5 $Q6_{5,1}$ 9.4 $\rho_{1,4}$ 15000 $A_{3,3,3}$ 418 $E_{3,6,3}$ 531.4 $Q3^{'}_{1,2}$ 34 $Q6_{6,1}$ 9.9 $\rho_{1,5}$ 14900 $A_{3,4,4}$ 656 $F_{3,2}$ 352.7 $Q3^{'}_{2,1}$ 34 $Q6^{'}_{1,2}$ 3 $\rho_{2,1}$ 10000 $A_{3,5,5}$ 626 $F_{5,2}$ 228.4 $Q3^{'}_{3,1}$ 34 $Q6^{'}_{2,1}$ 3 $\rho_{2,2}$ 10000 $B_{1,1,1}$ 150 $Q1_{1,2}$ 40.3 $Q3^{'}_{6,1}$ 34 $Q6^{'}_{3,1}$ 3 $\rho_{2,3}$ 10000 $B_{1,2,1}$ 150 $Q1_{2,1}$ 34.7 $Q4_{1,1}$ 8.7 $Q6^{'}_{6,1}$ 3 $\rho_{2,4}$ 10000 $B_{1,3,1}$ 150 $Q1_{3,1}$ 32.8 $Q4_{2,1}$ 7.5 $Q7_{1,1}$ 10.1 $\rho_{2,5}$ 9950 $B_{1,4,2}$ 150 $Q1_{5,1}$ 37.6 $Q4_{3,1}$ 7.1 $Q7_{2,1}$ 8.7 $\rho_{3,1}$ 501.4 $B_{1,5,2}$ 149 $Q1_{6,1}$ 39.4 $Q4_{5,2}$ 8.1 $Q7_{3,1}$ 8.19 $\rho_{3,2}$ 577.1 $B_{2,5,2}$ 199 $Q1^{'}_{1,2}$ 12 $Q4_{6,2}$ 8.5 $Q7_{5,2}$ 9.4 $\rho_{3,3}$ 600 $C_{2,1,1}$ 200 $Q1^{'}_{2,1}$ 12 $Q4^{'}_{1,1}$ 2.6 $Q7_{6,2}$ 9.84 $\rho_{3,4}$ 474.3 $C_{2,2,2}$ 200 $Q1^{'}_{3,1}$ 12 $Q4^{'}_{2,1}$ 2.6 $Q7^{'}_{1,1}$ 3 $\rho_{3,5}$ 435.7 $C_{2,3,3}$ 200 $Q1^{'}_{6,1}$ 12 $Q4^{'}_{3,1}$ 2.6 $Q7^{'}_{2,1}$ 3 $A_{1,1,1}$ 150 $C_{2,4,6}$ 200 $Q2_{1,2}$ 26.9 $Q4^{'}_{6,2}$ 2.6 $Q7^{'}_{3,1}$ 3 $A_{1,2,2}$ 150 $C_{3,1,1}$ 672 $Q2_{2,1}$ 23.1 $Q5_{1,1}$ 20.16 $Q7^{'}_{6,2}$ 3 $A_{1,3,3}$ 150 $C_{3,2,2}$ 578 $Q2_{3,1}$ 21.8 $Q5_{2,1}$ 17.3 $Q8_{3,2}$ 1210.8 $A_{1,4,4}$ 150 $C_{3,3,3}$ 546 $Q2_{5,1}$ 25.0 $Q5_{3,1}$ 16.4 $Q8_{5,2}$ 696.5 $A_{1,5,5}$ 149 $C_{3,4,6}$ 656 $Q2_{6,1}$ 26.2 $Q5_{5,2}$ 18.8 $Q8^{'}_{3,2}$ 247.9 $A_{2,1,1}$ 200 $C_{3,5,5}$ 626 $Q2^{'}_{1,2}$ 8 $Q5_{6,2}$ 19.7 $Q8^{'}_{5,2}$ 247.9 $A_{2,2,2}$ 200 $E_{2,1,3}$ 162 $Q2^{}_{2,1}$ 8 $Q5^{'}_{1,1}$ 6 $Q9_{3,1}$ 79.1 $A_{2,3,3}$ 200 $E_{2,2,5}$ 162 $Q2^{'}_{3,1}$ 8 $Q5^{'}_{2,1}$ 6 $Q9_{5,1}$ 45.5 $A_{2,4,4}$ 200 $E_{2,3,5}$ 162 $Q2^{'}_{6,1}$ 8 $Q5^{'}_{3,1}$ 6 $Q9^{'}_{3,1}$ 16.2 $A_{2,5,5}$ 199 $E_{2,6,3}$ 162 $Q3_{1,2}$ 114.2 $Q5^{'}_{6,2}$ 6 $Q9^{'}_{5,1}$ 16.2 $A_{3,1,1}$ 672 $E_{3,1,3}$ 544.3 $Q3_{2,1}$ 98.3 $Q6_{1,2}$ 10.1
 [1] Nguyen Van Thoai. Decomposition branch and bound algorithm for optimization problems over efficient sets. Journal of Industrial and Management Optimization, 2008, 4 (4) : 647-660. doi: 10.3934/jimo.2008.4.647 [2] Jing Zhou, Cheng Lu, Ye Tian, Xiaoying Tang. A SOCP relaxation based branch-and-bound method for generalized trust-region subproblem. Journal of Industrial and Management Optimization, 2021, 17 (1) : 151-168. doi: 10.3934/jimo.2019104 [3] Z.G. Feng, K.L. Teo, Y. Zhao. Branch and bound method for sensor scheduling in discrete time. Journal of Industrial and Management Optimization, 2005, 1 (4) : 499-512. doi: 10.3934/jimo.2005.1.499 [4] Shaojun Zhang, Zhong Wan. Polymorphic uncertain nonlinear programming model and algorithm for maximizing the fatigue life of V-belt drive. Journal of Industrial and Management Optimization, 2012, 8 (2) : 493-505. doi: 10.3934/jimo.2012.8.493 [5] Xiaohong Chen, Kui Li, Fuqiang Wang, Xihua Li. Optimal production, pricing and government subsidy policies for a closed loop supply chain with uncertain returns. Journal of Industrial and Management Optimization, 2020, 16 (3) : 1389-1414. doi: 10.3934/jimo.2019008 [6] Xue-Yan Wu, Zhi-Ping Fan, Bing-Bing Cao. Cost-sharing strategy for carbon emission reduction and sales effort: A nash game with government subsidy. Journal of Industrial and Management Optimization, 2020, 16 (4) : 1999-2027. doi: 10.3934/jimo.2019040 [7] Kun Fan, Wenjin Mao, Hua Qu, Xinning Li, Meng Wang. Study on government subsidy in a two-level supply chain of direct-fired biomass power generation based on contract coordination. Journal of Industrial and Management Optimization, 2022  doi: 10.3934/jimo.2022049 [8] Jing Zhou, Zhibin Deng. A low-dimensional SDP relaxation based spatial branch and bound method for nonconvex quadratic programs. Journal of Industrial and Management Optimization, 2020, 16 (5) : 2087-2102. doi: 10.3934/jimo.2019044 [9] Xin Zhang, Jie Wen, Qin Ni. Subspace trust-region algorithm with conic model for unconstrained optimization. Numerical Algebra, Control and Optimization, 2013, 3 (2) : 223-234. doi: 10.3934/naco.2013.3.223 [10] Michele Gianfelice, Marco Isopi. On the location of the 1-particle branch of the spectrum of the disordered stochastic Ising model. Networks and Heterogeneous Media, 2011, 6 (1) : 127-144. doi: 10.3934/nhm.2011.6.127 [11] Burak Ordin, Adil Bagirov, Ehsan Mohebi. An incremental nonsmooth optimization algorithm for clustering using $L_1$ and $L_\infty$ norms. Journal of Industrial and Management Optimization, 2020, 16 (6) : 2757-2779. doi: 10.3934/jimo.2019079 [12] Jiao-Yan Li, Xiao Hu, Zhong Wan. An integrated bi-objective optimization model and improved genetic algorithm for vehicle routing problems with temporal and spatial constraints. Journal of Industrial and Management Optimization, 2020, 16 (3) : 1203-1220. doi: 10.3934/jimo.2018200 [13] Wen-ling Zhao, Dao-jin Song. A global error bound via the SQP method for constrained optimization problem. Journal of Industrial and Management Optimization, 2007, 3 (4) : 775-781. doi: 10.3934/jimo.2007.3.775 [14] Ian Johnson, Evelyn Sander, Thomas Wanner. Branch interactions and long-term dynamics for the diblock copolymer model in one dimension. Discrete and Continuous Dynamical Systems, 2013, 33 (8) : 3671-3705. doi: 10.3934/dcds.2013.33.3671 [15] João Borges de Sousa, Bernardo Maciel, Fernando Lobo Pereira. Sensor systems on networked vehicles. Networks and Heterogeneous Media, 2009, 4 (2) : 223-247. doi: 10.3934/nhm.2009.4.223 [16] Wolfgang Riedl, Robert Baier, Matthias Gerdts. Optimization-based subdivision algorithm for reachable sets. Journal of Computational Dynamics, 2021, 8 (1) : 99-130. doi: 10.3934/jcd.2021005 [17] Xiangyu Gao, Yong Sun. A new heuristic algorithm for laser antimissile strategy optimization. Journal of Industrial and Management Optimization, 2012, 8 (2) : 457-468. doi: 10.3934/jimo.2012.8.457 [18] Adil Bagirov, Sona Taheri, Soodabeh Asadi. A difference of convex optimization algorithm for piecewise linear regression. Journal of Industrial and Management Optimization, 2019, 15 (2) : 909-932. doi: 10.3934/jimo.2018077 [19] Jianjun Liu, Min Zeng, Yifan Ge, Changzhi Wu, Xiangyu Wang. Improved Cuckoo Search algorithm for numerical function optimization. Journal of Industrial and Management Optimization, 2020, 16 (1) : 103-115. doi: 10.3934/jimo.2018142 [20] Yong Wang, Wanquan Liu, Guanglu Zhou. An efficient algorithm for non-convex sparse optimization. Journal of Industrial and Management Optimization, 2019, 15 (4) : 2009-2021. doi: 10.3934/jimo.2018134

2020 Impact Factor: 1.801

## Tools

Article outline

Figures and Tables